Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Yorba Linda?
Gate parts and welding in Yorba Linda typically run $150 to $900 depending on what’s involved, with most single-part repairs or small weld jobs landing between $250 and $450. A replacement operator board or a set of new hinges sits at the low end; a sagging gate that needs re-welding, realignment, and a new latch sits at the high end. The written estimate you get after we look at the gate is what sets your final price. We answer 24/7, dispatch between 7am and 7pm Sunday through Friday, and estimates are free.
If your gate is stuck open, dragging on the ground, or clicking but not moving, call (855) 382-4716. We’ll tell you what’s likely going on, then come out and confirm it on-site.
Gate Parts & Welding Cost Breakdown (2026)
These are the ranges we see across Yorba Linda driveways and light-commercial entries. Every gate is different, and a hinge that fits one gate won’t fit another, so treat these as planning numbers, not quotes.
| Item | Typical Estimated Range |
|---|---|
| Hinge replacement (per hinge, welded or bolt-on) | $150 – $350 |
| Weld repair on a sagging or cracked gate frame | $250 – $600 |
| Roller, track, or guide replacement (slide gates) | $180 – $500 |
| Latch, stop, or catch hardware replacement | $150 – $300 |
| Operator control board replacement | $350 – $800 |
| Photocell (safety sensor) pair replacement | $200 – $400 |
| Loop detector repair or replacement | $300 – $750 |
| Gate motor or gear replacement | $400 – $900 |
| Arm or actuator replacement | $350 – $700 |
| Full hinge and hardware rebuild | $500 – $1,200 |
A few things push the number up. The gate’s material matters: a steel frame that’s been welded before takes longer to re-weld cleanly than a fresh one, and aluminum needs different rod and technique than steel. Operator brand matters too. We carry parts and knowledge for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, and knowing how a specific board or sensor is supposed to behave shaves diagnostic time off the bill. A commercial-grade operator on an HOA entry runs more than a residential driveway unit, both in parts and in the time it takes to test safely.
What pulls the number down: catching a worn hinge before it tears the gate frame, replacing a sensor before the board takes the fault, and having the operator model number ready when you call so we can check parts before we arrive. That last one saves a trip.
What Affects Gate Parts & Welding Pricing in Yorba Linda
- Gate material and condition. A rusted steel frame that needs grinding before it can be welded takes longer than a sound one. Aluminum and steel weld differently, and the finish you want after the weld changes the labor.
- Manual versus electric. A manual gate is hardware and welding. An electric gate adds an operator, sensors, and wiring to the picture, and electric gate repair is one of our core services because that’s where most of the real cost sits.
- Brand-specific parts. We carry parts and knowledge for the major operators, but a control board for a DoorKing access system and a board for a Mighty Mule residential opener are not the same price, and the diagnostic path to each is different. Brand-specific logic beats guesswork when the bill is hourly plus parts.
- Residential versus light-commercial. HOAs, multi-unit entries, and small commercial drives use heavier gates, heavier operators, and more safety hardware. Expect the upper half of the ranges on those jobs.
- Hillside lots and slope. Many Yorba Linda properties sit on sloped driveways, and a gate on a grade stresses its hinges differently than a flat one. Gravity works against a gate that isn’t hung true, and that shows up in how often it needs re-welding.
- Access and gate size. A wide driveway gate or one hemmed in by landscaping takes more handling. Heavy panels need support and care while they’re off their hinges, and that’s labor.
What the Repair Actually Involves
Most gate part and welding calls follow the same shape, whether you’re in a Yorba Linda neighborhood off Imperial Highway or up a hillside street. We look at the gate first, not the operator. We check whether the gate swings or slides freely by hand, whether the posts are sound, and whether the hinges or rollers are carrying the panel the way they should. A gate that binds by hand will stress an operator until the operator fails, so fixing the hardware first protects the electronics.
From there it’s a matter of matching the failure to the cause. A gate that sags usually needs a hinge or a weld at the frame, not a new operator. A gate that runs partway and reverses is usually a sensor or loop issue. A gate that clicks but doesn’t move is usually a board, a capacitor, or a motor. We work through that in order, and we tell you what we found before we touch anything.
Safety is part of the job here. Gate operators run on line voltage, and the safety sensors exist for a reason: a heavy panel that closes on a person or a vehicle causes real injury and real damage. We don’t recommend DIY work on operator wiring, control boards, or anything that involves the power supply. That’s training and test-equipment territory, and getting it wrong can hurt someone. If your gate is electric and misbehaving, leave the power alone and let us look at it.
How to Save on Gate Parts & Welding in Yorba Linda
- Get the model number before you call. On the operator housing there’s usually a label with the make and model. Knowing it’s a LiftMaster or a FAAC before we arrive lets us check parts and arrive prepared, which shortens the visit.
- Fix the hardware before the operator pays for it. A binding hinge left alone will wear out a motor or a board. Catching it early is the cheapest repair you’ll make all year.
- Address one failing sensor, not the whole system. We test each photocell and loop individually so you’re not replacing parts that are working fine.
- Get the free estimate in writing. We’ll walk the gate with you and put the parts and labor on paper before any work starts. That estimate is what sets your final price, so there are no surprises.
- Plan for the whole gate, not just today’s part. If a gate is at the end of its hardware’s life, sometimes a hardware rebuild costs less over two years than three separate repairs. We’ll tell you honestly which is which.
When you’re ready, call (855) 382-4716 for a free estimate. We answer 24/7 and dispatch from 7am to 7pm, Sunday through Friday.
Repair or Replace? A Straight Answer on Gate Parts
Repair is usually the right call when the gate frame and posts are sound and the failure is in a part: a hinge, a roller, a sensor, a board. Welding a solid frame back into true costs a fraction of a new gate, and it keeps the gate you already know fits your driveway.
Replacement makes more sense when the frame is rusted through in multiple places, when the posts have moved, or when an older operator has started failing part by part with no end in sight. On a light-commercial entry where downtime costs money, a worn operator that’s been patched twice is often better replaced than patched a third time. We install new gates as well as repair and upgrade them, so you’re not hunting for a second vendor when the answer turns out to be replacement. Wherever the decision lands, the choice belongs to you, and we’ll lay out both options plainly.
FAQs – Gate Parts & Welding Cost
How much does gate welding cost in Yorba Linda?
Gate welding in Yorba Linda typically runs $250 to $600 for a frame repair on a sagging or cracked gate, and $500 to $1,200 for a fuller hinge and hardware rebuild. The range depends on gate material, how much prep the old weld needs, and how the gate is supported during the work. Call (855) 382-4716 for a free estimate that reflects your actual gate.
How much does an electric gate repair cost?
Most electric gate repairs land between $200 and $800, with the low end covering a sensor or photocell and the high end covering a control board or motor. Board and motor work sits at the top because parts cost more and testing takes longer. Call (855) 382-4716 for an exact quote; estimates are free.
Is it cheaper to repair my gate or replace it?
Repair is cheaper in most cases where the frame is sound and one or two parts have failed, often a few hundred dollars against a full replacement. Replacement is the better value when the frame is rusted through or the posts have shifted. We’ll show you what we see and let you decide. Call (855) 382-4716 to talk it through.
Can you come today?
Same-day service is often possible, and we dispatch from 7am to 7pm, Sunday through Friday. We’re closed Saturday. Call (855) 382-4716 and we’ll get you on the schedule; we answer the phone 24/7.
Do you work on my gate brand?
We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, across both residential driveway gates and light-commercial access systems. If you’re not sure of your model, the label on the operator will tell us. Call (855) 382-4716 for a free estimate.
Gate Repair and Parts in Yorba Linda
Gate Repair Yorba Linda has focused on gates since 2011, and that gate-only focus is why we know how a specific board or hinge fails rather than treating it like a general handyman job. We handle repair, electric gate repair, and new installation for homeowners, property managers, and light-commercial sites, and we’ve served gate repair in Yorba Linda for 15 years. If your gate is stuck, slow, noisy, or silent, the answer usually starts with a look and a written estimate. Call (855) 382-4716. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Whether you’re working through gate repair in Yorba Linda for a residential driveway or sorting out a commercial entry, the estimate comes first, and it’s free. Call us and let’s get your gate moving.
Pricing reflects the Yorba Linda market as of 2026. Gate Repair Yorba Linda offers free estimates – call (855) 382-4716.
What Our Customers Say
"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Ernesto Flores"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
- Nicole Fletcher"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Ramon Vargas